Epson WorkForce 600 Setup

Unpack The Epson WorkForce 600 Printer

Remove the cover over the Epson WorkForce 600 printer carton to open it.

The Epson WorkForce 600 Setup and its components are given in the printer box.

The components are the power cable, ink cartridges, Ethernet cord, and software installation CD.

Set Up The Epson WorkForce 600 Printer’s Power Connection

Plug one end of the cable to the power port of the Epson WorkForce 600 printer and the other terminal to a power source directly.

Lift the control panel of the printer.

Tap the ON key on the front panel.

Configure the settings like the Language, Country/Region, Date, and Time.

Insert The Cartridges Into Their Holders Of The Printer

Open the scanner unit at the top of the Epson WorkForce 600 printer.

Raise the cartridge cover of the Epson printer.

Rock the ink cartridges provided in the printer box for 4 to 5 times.

Remove the cartridges from its package.

Peel off the tapes on cartridges.

Insert the cartridges into the respective holders of the printer.

Gently press the cartridges until they fit into the slots.

Close the access cover of the cartridges and scanner unit.

Tap the OK key on the control panel of the printer.

Load Enough Sheets In The Paper Tray

Open the paper support and pull the extensions.

Extend the output tray and open the stopper.

Move the feeder guard forward.

Squeeze the edge guide and slide it to the left printer.

Take a bunch of sheets and tap them on a flat surface.

Keep the sheets against the edge guide.

Make sure that the sheets are placed with their printable side facing up.

Slide over the edge guide and flip the feeder guard back.

Attach The Power Cable

Unpack the power cord provided in the Epson WorkForce 600 Setup box.

Plug one end of the telephone wall jack and the other end to the LINE port of the printer.

Install The Printer Software To Your Computer

Download the Epson WorkForce 600 printer software on your computer.

Install the software once you download it.

Connect the printer to your computer while installing the printer software.

Comments

Post a Comment

Popular posts from this blog

HP Smart Tank 515 Wireless Setup

 Check to ensure that your HP Smart Tank 515 printer’s hardware setup is completed and ready for the wireless setup. Gather your wireless network’s credentials, such as SSID and password. Ensure that your computer (that you're using) is connected to the same network to which you’re about to connect the printer.  Check if your printer is in network setup mode. If not, restore the network settings of your printer to default to enable the network setup mode. To do so, follow the instructions below. Make sure that your HP Smart Tank printer is turned on. Locate the Wi-Fi and Cancel buttons on your printer’s control panel. Now, hold down both the buttons at the same time. Release the buttons after five seconds. Now, your printer’s network settings will be restored. *Note: You can also use your printer’s EWS page to restore its network settings. Download and run the HP Smart Tank 515 printer software on your computer. When prompted, select the Wi-Fi Connection option and follow the ...
Read more

BROTHER MFC-T4500DW SETUP

 Quick instructions to set up the Brother MFC-T4500DW multi-function color printer Open your Brother printer's product box. You can find the Brother MFC-T4500DW printer, a set of ink bottles, a quick setup guide, a product safety guide, a power cord, an installation disc, USB interface cable, and telephone line cord. Now, take all the components and the printer out of the box. Unpack your printer completely by removing the packing tapes or materials surrounding or present inside & outside the printer. Place the Brother printer on a clean surface area.  Now, remove the printer's paper tray. Based on the paper type that you're loading, align the paper width guides correctly. Load a stack of paper in the tray and place the tray back into the printer. Connect your Brother printer to an electrical outlet and turn it on. Once the printer becomes stable, set the basic printer preferences by following the instructions displayed on the printer screen. After setting them, open th...
Read more

Xerox Versalink C7025 Setup

 XEROX VERSALINK C7025 UNBOXING SETUP Initially, take the Xerox printer out of the box and unpack it completely. Place the unpacked printer on a clean surface. Now, get the toner cartridges provided along with the printer box. Shake the cartridges before unpacking them. Now, open your Xerox printer’s front door. Install the unpacked toner cartridges one by one into their slots and close the front door. Pull out your printer’s front tray. Align the width guides and load paper in the tray. After loading the paper, adjust the width guides correctly and push the tray towards the printer. If necessary, install the optional components into the printer. Now, connect your printer to an electrical outlet and turn it on. Next, you need to set the initial settings of the printer. Perform the initial setup by following the on-screen instructions. Once it is done, begin the printer software installation on your computer. Finally, perform a test print operation to check whether the Xerox VersaL...
Read more