Canon Pixma TS702 Setup

 Canon Pixma TS702 Printer Setup Guidance

UNPACK

Unbox the printer and check if the other printer accessories are present in the box.

Remove the packaging materials and the protective tapes from the printer.

Lift the printer’s top cover, then peel off the tapes from the inside of the printer and close the top cover.

SWITCH ON THE PRINTER

Hook up one end of the power cord to the printer and plug the other end to an electrical socket. 

Now, press the power button on the control panel to switch on the printer, after which the printer display turns on.

Set the language using the control panel and press the OK button.

INSERT INK TANKS

Again, open the top cover, wait till the print head stops moving, then unpack the new ink tank.

Remove the orange film and cap from the tank, install the ink tank into the print head and gently press it such that it locks into

Verify if the ink indication mark appears on the display panel.

Similarly, install all the other ink tanks in the printer and close the top cover of the Canon Pixma TS702 setup.

After that, check the display panel for a message and press OK.

LOAD PAPER TO THE PAPER CASSETTE

After you install the ink tanks, when the message saying to start the alignment appears on the display,  press Yes.

Slowly take out the paper cassette from the printer; then take off the cassette cover.

Move the paper guides to the paper size you are loading.

Neatly arrange the paper such that the print side is down, against the front paper guide in the cassette.

Then shift the paper guides to fit the paper size, but see that you do not squeeze the paper.

Replace the paper cassette cover and then insert the cassette into the printer.

Draw the paper output tray outwards until it stops, and see if there is any protective material, then remove it.

Extend the paper output support, which is below the paper cassette.

Check the messages on the printer’s display panel, respond in an appropriate way.

INSTALL THE PRINTER SOFTWARE

When the physical setup is complete, proceed to install the printer software on your computer for easy functioning.


Comments

Post a Comment

Popular posts from this blog

HP Smart Tank 515 Wireless Setup

 Check to ensure that your HP Smart Tank 515 printer’s hardware setup is completed and ready for the wireless setup. Gather your wireless network’s credentials, such as SSID and password. Ensure that your computer (that you're using) is connected to the same network to which you’re about to connect the printer.  Check if your printer is in network setup mode. If not, restore the network settings of your printer to default to enable the network setup mode. To do so, follow the instructions below. Make sure that your HP Smart Tank printer is turned on. Locate the Wi-Fi and Cancel buttons on your printer’s control panel. Now, hold down both the buttons at the same time. Release the buttons after five seconds. Now, your printer’s network settings will be restored. *Note: You can also use your printer’s EWS page to restore its network settings. Download and run the HP Smart Tank 515 printer software on your computer. When prompted, select the Wi-Fi Connection option and follow the ...
Read more

BROTHER MFC-T4500DW SETUP

 Quick instructions to set up the Brother MFC-T4500DW multi-function color printer Open your Brother printer's product box. You can find the Brother MFC-T4500DW printer, a set of ink bottles, a quick setup guide, a product safety guide, a power cord, an installation disc, USB interface cable, and telephone line cord. Now, take all the components and the printer out of the box. Unpack your printer completely by removing the packing tapes or materials surrounding or present inside & outside the printer. Place the Brother printer on a clean surface area.  Now, remove the printer's paper tray. Based on the paper type that you're loading, align the paper width guides correctly. Load a stack of paper in the tray and place the tray back into the printer. Connect your Brother printer to an electrical outlet and turn it on. Once the printer becomes stable, set the basic printer preferences by following the instructions displayed on the printer screen. After setting them, open th...
Read more

Xerox Versalink C7025 Setup

 XEROX VERSALINK C7025 UNBOXING SETUP Initially, take the Xerox printer out of the box and unpack it completely. Place the unpacked printer on a clean surface. Now, get the toner cartridges provided along with the printer box. Shake the cartridges before unpacking them. Now, open your Xerox printer’s front door. Install the unpacked toner cartridges one by one into their slots and close the front door. Pull out your printer’s front tray. Align the width guides and load paper in the tray. After loading the paper, adjust the width guides correctly and push the tray towards the printer. If necessary, install the optional components into the printer. Now, connect your printer to an electrical outlet and turn it on. Next, you need to set the initial settings of the printer. Perform the initial setup by following the on-screen instructions. Once it is done, begin the printer software installation on your computer. Finally, perform a test print operation to check whether the Xerox VersaL...
Read more